RWD SR20 Civic Part 4 – Its starting to come together

front on ground
RWD SR20 Civic Part 3
August 28, 2014
10426324_529115427221652_6916300030606883149_n
Stadium Drift Final – Results with plenty of photos
September 11, 2014
photo 4 (2)

The guys have been busy over the past week, We had a clear goal in mind. Get the rear end in the car and keep it rolling, we dont even know if the rear end will fit the stock body so the sooner we got it in we could see how much we need to change to have the car sitting well and rolling true.10660645_10153115540397729_47485825_n

 

As you can see, there isn’t a lot of room for activities back here. We knew we were going to lose our spare wheel, but after pulling it down our direction changed to making sure we didn’t lose the back seat as well. We still had to tunnel the car and somehow fit a fuel tank under the car to meet engineering requirements. The car will be street driven so we cant run fuel cells or have big fuel tanks hanging off the back of the body.

10643185_10153115540202729_978685678_n

 

The view from inside isn`t much better. To keep the back seats we ned to retain the factory mounting points, These are located on each wheel arch as well as the dead centre of the car. Daniel (Grub) wanted to use the same method as the front end and use the S15 strut tops in the rear instead of fabricating  new tops. The main goal for this car is to look factory, by using the factory strut tops and some sealant we believe we can achieve the factory look.

10541913_10153115540327729_925405711_n

 

It was time to string line the rear end and remove it from the car, we wanted to keep the geometry the same as the 200sx as this is a car we know how to set-up. They have great traction when you want them too as well as a very predictable power “over-steer”, this is something we didn’t want to lose when driving the civic so we spent a lot of time studying the angles of both the wheel and the shocks of the s15 before we pulled it apart.

10660640_10153115540477729_9342823_n

 

Once the rear end was out of Big Yella we could really gauge how much work we had to do to get the Nissan rear end in the car. The only other EG that has been done with a Nissan rear end was a drift car and the could run a fuel tank in the boot and didnt see a reason to ever take it out again, so the welded it in place. This is something we wanted to avoid, Grub came up with another stroke of genius. His plan was to pull the factory pins out of the S15 chassis and mount them in the Civic body, this means that we could unbolt the rear end with 4 bolts and drop it out and replace it with any S chassis rear end. So if we wanted to upgrade arms, diffs, bushes etc it could all be done with ease. The downside was that there was now alot more work to do…

10643234_10153115540907729_693610885_n

Out comes Grubs famous Magic pen, and he removed the spare wheel well and made room for the new 200sx rear end.

10617336_10153115541107729_1727895013_n

 

Once the floor came out it all started to make more sense, we could now see how things would start to be fitted, with some minor adjustments we had enough clearance to trail fit the rear end and see where these mounts needed to be placed.

10622077_10153115540792729_224191061_n

 

We already knew that the rear end is almost the exact same width in both cars, this made our job slightly easier ( but not much) What we are checking here is the clearance for the rear cradle mounts. Then Grub will have to fabricate mounting points off the body to mount the pins in.

10660966_10153115541427729_1733679633_n

aligning the hub to the centre of the wheel arch proved to be very tricky, we needed clearance at the front and rear of the wheel and to get this we had to mount the wheel about 10mm forward of the centre point. Now it is time to start making the mounts.

photo 2

 

These are the pins that Grub had to remove with his magic pen from the S15 Chassis, now the fun part of removing them from these blocks.. (only took 3 hours)

Rearplate

 

This is the start of the rear mounts, we want to keep it as neat as possible so we will mount the pins through this then sheet it all off, No one will ever know.

10660936_10153115541262729_1785069664_n

Once the front part of the cradle was in, it was time to focus on making the mounts for the top pins… It made it a lot easier to do with a big hole in the floor.

10589782_10153115541602729_2130480186_n (1)

 

This is often the most time consuming part of any build. Levelling off and making sure the numbers in your head (on paper) match the numbers you see in front of you.

 

 

 

 

10654066_10153115541737729_1743363262_n

Daniel (grub) actually used the same technique as the factory would use to lock these pins in place, they use a lock ring to hold them in but can be removable if needed.

impossiblefabricationspin

 

By welding the lock ring in place it means that we can remove the pins if needed, along with it being a tried and tested mounting technique.

Impossiblefabricationpins2

 

This is what the pins look like once mounted and ready to install in the car.

 

10643274_10153115541842729_36836389_n (1)

Photos just dont do it Justice, We sat on the floor of the workshop for more than an hour looking at the rear end of the civic. It looks so tough with 245 wide tyres and the diff looks massive against the small body. Time to get back to work as we have to put shock towers in.

10643334_10153115542022729_1417983447_n

After unpicking the rear shocks out of the S Chassis, it was time for a clean up and time to tack it in its final resting place.

10660894_10153115542097729_1023442473_n

Although it looks very rough here, this is actually a work of art, it took us no less than 1 day per side to get the angle and height correct, the distance between the wheel and the tower is critical to how this car will handle. We are glad that the boys at Impossible Fabrication have been to a few rodeos before and knew some little tricks to make this process easier.

 

10654130_10153115542172729_934778275_n

The moment of truth, time to set the Civic down on its new rear end. Once we are happy with it we will remove the blue bars on the towers and reinforce them so they will be stronger than a factory tower, (we have a few tricks up our sleeve for that).

photo 4 (2)

 

We couldn’t be happier with the way the car sits in the rear, the wheels tuck just enough to give it a good stance, We can run a 265 tyre (if needed) and 17inch wheels almost look to big on it.

NUloncivicrearend

 

 

Next up we are going to sheet the rear end and start work on the tunnel. We only have 2 weeks to “Racewars” (Nulon Nationals) and we hope to at least have the car there to show people.

 

 

 

 

 

 

 

 

Comments

comments

Comments are closed.